|
Great new rec/tech wings we've started carrying. We
brought in This and the Torus 49, although we can get any of their wings that
you may desire for your single or double tank needs.
This kit includes;
Torus 38, Full Circle Style Doubles Wing W/ 30 mil
bladder
30 mil (.030 inches) Thick Bladders, Thickest Bladders Available!
Most wings use 12 mil, some use 15 mil, a few use 25 mil. No other brand of
wings offers ultra thick 30 mil urethane bladders.
No Zipper! These new wings are sewn shut. The new heavy duty 30 mil urethane
bladder material eliminates the need to access the bladder via a zipper. No
zipper to fail, or get pinched between the tank and plate. Simple, clean clutter
free wing design.
30 mil urethane RF welded inner bladder. Most wing bladders are .012 inches to
.015 inches in thickness. At .030 inches (30 mil) DSS bladders offer Improved
resistance to impact damage.
Rugged Construction 1050 Ballistic Nylon Outer Shell, Sewn throughout with #138
Bonded Nylon thread, top stitched for extra seam strength.
One OPV or Rear Dump. Mounted on the diver’s left, on the diver’s side of the
wing. Equipped with a knotted pull cord.
Simple Elbow. No rapid exhaust or pull Dump on the 16 inch Inflator Hose, 18
inch Lp Hose and Lp hose release are included with every wing. Generic Power
Inflator widely used in the industry, making parts and service easily available.
More about the Zipper less Design. New materials permit new designs. There are
successful wing designs that use zippers, but zippers have never been my first
choice. They add cost, can jam, can be difficult to install, and difficult to
use. They can’t be installed on a compound curve, and make the wing stiff and
non compliant. They add bulk when packing. All of our wings that use zippers
have short, heavy duty zippers. These are always installed on a simple curve.
Why have a zipper at all?
In a wing that uses a sewn outer shell and a welded inner bladder (so called
double bladder designs) the zipper provides access to install, repair, or
replace the bladder......in theory anyway.
Some minor pinch flats can be repaired without removing the bladder, by opening
the zipper and applying glue or patches. These easy field repairs are a benefit
of double bladder designs. The use of a very thick (30 mil vs.12 mil) urethane
for the inner bladder greatly reduces the chances of damage occurring to the
inner bladder, making zippered access largely unnecessary.
If a wing should require a replacement bladder this can be easily accomplished
by returning the wing to DSS. Most repairs are completed in 1-2 days.
Pro-Fit Stainless Steel BackPlate, Medium
Precision Waterjet cut from heavy 11 gauge (.118” thick) 300 Series Stainless
Steel. Medium size fits most divers from 5 ft. 3 in. to 6 ft. 0 in. 4.7 lbs.
DSS back plate features angled harness slots and a much flatter profile than
other plates. This results in greater comfort and a lower profile when used with
a single tank.
Single tank cam strap slots are located to avoid interference with harness
webbing.
Large diameter holes located near the plate edge permits easy attachment of clip
on accessories. This not possible with stamped plates.
All load bearing webbing slots have tough thermoplastic elastomer grommets over
molded, permanently bonded to plate for zero webbing wear.
Dive Doubles? No Problem Holes and slots are provided at 11” centers for
mounting Double tanks. Lower Slots allow easy mounting of doubles with bands
that are not exactly at 11” centers.
All edges and holes are carefully deburred. Vibratory abrasive finished to a
uniform satin surface.
Uniformly bent using one shot bending die to ensure consistent flatter profile.
Single Piece Hogarthian Harness
Includes:
12 ft of 2inch resin reinforced webbing
2 each Bent 2 inch Drings
3 each unbent 2 inch Drings
3 each serrated webbing keeper
1 Plain Webbing Keeper
1 Custom Webbing Keeper
1 each waist buckle
1 sewn soft webbing crotch strap
1 each Dalton Safety Knife and Sheath
3 each Bicycle Inner tube Loops
12 ft #24 braided Nylon Line
Notes:
1. Some of these items may not appear in the photo.
2. The Crotch Strap assembly consists of:
43 inch Soft edged 2 inch webbing
1 sewn in unbent 2 inch Dring (scooter ring)
1 Plain Keeper to attach crotch strap to plate
1 Loose unbent Dring (butt dring)
1 Custom Keeper to mount Butt dring
Crotch strap is furnished assembled with these parts
Q-Tach Retainers, Pair (fit DSS plates only)
The Q-Tach Retainers make the Delrin Thumbwheels “Captive”
The Q-Tach Retainers are secured to the back plate (may not fit all makes of
Back Plates) and accept the Delrin Thumbwheels. No more loose wing nuts to
loose. Also molded from tough, springy Delrin, the retainers snap on to the
Delrin Thumbwheels. Different size thumbwheels can be fitted in seconds.
Furnished with required hardware.
|
